MODEL NUMBER:  STCII-61V-26CV-EFI

Engine:

General Type:       

• Heavy-duty industrial/commercial

Brand:                   

• Kohler

Model:                 

• ECV749

Horsepower:         

• 26 HP @ 3600 RPM

Type:                     

• 4 cycle gas, twin-cylinder, air-cooled, vertical shaft engine

Displacement:     

•  747 cc (45.6 cubic inch)

Cylinders:             

• 2 cast-iron cylinder liners

Governor:             

• Mechanical type governor with variable speed control set at 3600                            rpm (±75rpm), idle set at 1800 rpm (±75 rpm)

Air Intake Group: 

• Large capacity 2-stage canister air filter

Exhaust:               

• Side-mount single canister

Fuel Group:           

• Electronic fuel Injection system for maximum fuel efficiency. High pressure electric fuel pump with inline fuel filter. Choke free operation.

Oil Pump Group:   

• Full pressure lubrication with oil filter

Starter/Electrical: 

• 12 volt "maintenance-free" sealed battery (350 CCA) with alternator, solenoid shift starter with key start

Charging System: 

• 20 amp

Engine Deck:

Fuel Tank:             

• Dual tanks (9.5 gallons / 35.9 liters total) with extra-large easy-fill                            openings and over-sized fuel caps, remote mount switching valve,                          molded-in cup holder
  

Drive Wheels/Tires:     

• 24 x 12 - 12 four-ply pneumatic tubeless, radius edge, wide offset                          rims for better traction
  

Parking Brake:       

• Foot-operated brake with park lock feature.  AUSCO disc brakes                              feature a rotor and caliper style design for maximum holding power.
  

Frame:                   

• Compact frame design with structural steel tube construction, welded.                    Engineered for a low center-of-gravity for increased incline                                      performance.

Drive System:

Type:                     

• Hydro drive with two variable displacement pumps and two cast-iron                      wheel motors for independent control of each drive wheel
  

Hydro Pumps:     

• Two Hydro-Gear Model 12cc pumps with cooling fans feature dump                        valves for movement without running engine.  Built in pressure relief v                    valves add to hydraulic system life and reliability by reducing high                            pressure fluid spikes.
  

Drive Wheel Motors:       

• Two Parker 14.5 cubic inch cast-iron high-torque wheel motors
  

Transmission Belt Idler:   

• Self-adjusting, self-tightening, with permanently lubricated bearings
  

Hydro Fluid Cooling Group:     

• 4 qt. capacity nylon fluid reservoir, uses SAE 20W50 fluid and 10 micron filter
  

Steering/Travel Control:

• Twin lever fingertip steering control with gas shock dampeners for smooth, responsive control to each wheel
  

Axles:

• 1-1/4" heavy-duty, tapered motor shafts
  

Wire Harness:   

• 14- and 16-gauge wire.  Tightly wound protective wire loom.  Dielectric grease at major electrical connections.
  Safety Group:     
• Seat actuated engine kill, neutral interlock, mower engagement (PTO) switch, parking brake
  

Instrument Panel:     

• Mounted at the right side of the operating position for easy access.  Key switch, throttle, fuses, PTO switch, Tiger Eye Advanced Monitoring System, and 12-volt      accessory outlet.
  

Forward Ground Speed Range:     

• 0 up to 12.0 mph

Reverse Ground Speed Range:     

• 0 up to 5.0 mph

Cutter Deck:

Type:

• Velocity Plus, floating, adjustable anti-scalping, hybrid design combines out-front and belly-mount designs, special raised front edge allows grass to enter the deck standing upright for a fast, manicured cut.
  

Construction:

• Tri-Plate construction consists of a 10-gauge steel cutter deck top reinforced with 10-gauge upper support plate and an 11-gauge lower spindle support plate. These three layers of steel equal close to a 1/2" thick steel cutter deck top.  Deck skirt is 7-gauge.  Trim side wear pad protects deck and landscape.
  

True Cutting Width:

• 52.0 inches (132.0 cm)
  

Cutting Height Adjustment:

• Foot-operated pedal adjustment with deck easy-access deck latch lever adjusts from operator’s seat, 1" to 5" in 1/4" increments.

Cutter Blades:

• Three (3) high-strength cutter blades
  

Cutter Deck Baffles:

• Velocity Plus deck baffles direct air flow for maximum quality-of-cut.  Custom Cut Baffle allows adjustment to individual cutting conditions (7 positions).
  

Blade Engagement:

• Electric PTO via Ogura GT3.5 (250 ft. lb) clutch brake with control panel knob
  

Discharge Baffles:

• Turbo-Baffle for extra discharge velocity with spring-loaded plastic discharge chute
  

Caster Wheels:

• 13 x 6.5 x 6 flat-free caster wheels(4-ply) with tapered roller bearing pivots and axles
  

Spindles:

• Heavy-duty 1-1/8" top dimension spindle shaft, cast housing, tapered roller bearing, low maintenance with top access grease fitting and grease overfill relief poppet
  

Idler Arms:

• Spring-loaded for continuous belt adjustment and longer life, permanently lubricated bearings
  

Spindle Pulleys:

• Split steel design with easily removed tapered hubs.  Split steel is stronger than stamped or cast-iron pulley designs.
  

Cutter Deck Belts:

• B-section with Kevlar cord
  

Anti-Scalp Rollers:

• Two front 4-1/2" adjustable, two rear 10" fixed

Approximate Dimensions:

Length:                                                                85.5"
Tracking Width:                                                   51.5"
Width:                                                                 73.5"
Width (with discharge in transport position):     62.75"
Height (with ROPS):                                            67.25"
Height (with ROPS folded down):                       46.75"
Turning Radius:                                                   Zero Radius Turning
Weight:                                                               1261 lbs.